Page 5 of 5
Posted:
Mon Feb 16, 2009 4:41 pm
by Tony
It probably does move quite a bit of air, but I very much doubt it would produce any useful pressure sufficient for our purpose.
From the Coke can, and the 5.5 Kw motor frame size, that rotor might possibly be around eight inches in diameter (?)
At 2,800 rpm, expect about 3.3 inches of developed air pressure. Not a lot.
For a direct coupled blower like this, the outside diameter of the blower casing needs to be AT LEAST two feet in diameter, and three feet in diameter would be even better. That is what we should be looking for.
Posted:
Mon Feb 16, 2009 5:22 pm
by FPV_GTp
Ok , doesnt sound good , but bought one and will test it and see what i can actually sequeeze out of the outlet.
cheers
Posted:
Mon Feb 16, 2009 5:41 pm
by Tony
Have a read through the "Air Movers" part of the forum, there is a lot of good stuff there about big blowers.
Racepumper has just bought this beauty
Posted:
Mon Feb 16, 2009 6:10 pm
by FPV_GTp
woooooooooooo Tony that unit Racepumper bought is a beauty
lucky devil , i bet he will get more blow for his money oops
cheers
Posted:
Mon Feb 16, 2009 6:45 pm
by Tony
One or two other people on the Forum have also found similar priceless treasures. It is a case of being patient and vigilant.
If I was Racepumper, and it turns out to only be a 3Hp motor, I would remove one blower and fit it to a 10 Hp motor. It can then be driven with his VFD to maybe 70 Hz or more to reach even higher flow and pressure.
Five inch inlet, three inch outlet, 2.5 foot casing, wow, that is PERFECT.
Posted:
Mon Feb 16, 2009 6:47 pm
by Tony
One or two other people on the Forum have also found similar priceless treasures. It is a case of being patient and vigilant.
If I was Racepumper, and it turns out to only be a 3Hp motor, I would remove one blower and fit it to a 10 Hp motor. It can then be driven with his VFD to maybe 70 Hz or more to reach even higher flow and pressure.
Five inch inlet, three inch outlet, 2.5 foot casing, wow, that is PERFECT.
Posted:
Tue Feb 17, 2009 4:52 am
by RACEPUMPER
More pics back in the air mover thread fellas, Tony I was a bit excited the other day and got a little carried away, I have the REAL measurements now :p
Jim
Posted:
Thu Mar 12, 2009 7:34 pm
by FPV_GTp
Posted:
Thu Apr 30, 2009 9:51 pm
by Flash
OK guys, help me out here. (New guy, first post)
I have just finished this thread and what i have got out of it......
The vac. motors are AC/DC capable motors.
That running them as DC motors will run better/cooler and more efficient then as a ac motor.............SOUND GRATE!!.......Why is this not done more often????
Also draws less amp in DC mode>>>????
When i was on this link, (that was previously posted)
the description said this:
KIT-067 and KTA-067 DC Motor Speed Controller
With this kit control the speed of any common DC motor rated up to 55V (5A) without sacrificing motor torque. Operates on a supply voltage of 5V to 15V.
Uses NE556 to pulse-width modulate a high current power MOSFET, IRFZ44.
In this way motor torque is maintained. Adjustable speed control.
Box mounted. Finished Dimensions (mm): 60Wx100Lx30H.
Download datasheet file
Hmmm??????55V (5A)
I thought that conversion was still a 120V just DC now?????
I'm no electrician, as you can tell already
:D
And is that all i need.....or do i need a 2nt elec. device, to do the AC to DC sign wave?????
A lot of Question for one post i know.........Just real confused...............
Thanks in advance
Flash
Posted:
Sat May 02, 2009 11:33 pm
by Flash
Bump^
Is, a DC conversion worth it?
Live in the USA so it would be a 110/120 AC conversion to DC
Plan on building a bench down the road.
Acutely have a vary, vary simple one built with a "car wash Vacuum" hooked to it..........but not enough Vac. Pulls 28" sealed, and goes down to 7" at .500 lift.(The manometer stays the same from .450" lift on up!)
Need more vac, and would be interested in your opinion and knowledge on the DC idea and other thought that might help with my beginning of this new venture.................
Posted:
Mon May 04, 2009 11:56 pm
by jsa
Posted:
Wed May 06, 2009 2:41 pm
by Flash
Posted:
Sat May 09, 2009 10:33 am
by montana
Hi
Im also from Australia and planning a bench build just wondering if this Speed controller would work. I will probably be using it for only one motor as it is 10A.
Thanks
Posted:
Sun May 10, 2009 7:55 am
by jsa
Hello and welcome, where in AU are you ?
That speed controller is for universal motors so should be fine for manual control of a vac motor.
Posted:
Sun May 10, 2009 5:42 pm
by Tony