[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4752: Cannot modify header information - headers already sent by (output started at [ROOT]/includes/functions.php:3887)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4754: Cannot modify header information - headers already sent by (output started at [ROOT]/includes/functions.php:3887)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4755: Cannot modify header information - headers already sent by (output started at [ROOT]/includes/functions.php:3887)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4756: Cannot modify header information - headers already sent by (output started at [ROOT]/includes/functions.php:3887)
Tractorsport Flowbench Forum Archive • View topic - KISS Pitot bench design

KISS Pitot bench design

Pitot Style Bench discussions

Postby Tony » Mon Jan 09, 2006 5:31 pm

Nick, here is a data sheet for the MXP5010:



Note that it MUST be powered from a five volt accurately regulated supply. A nine volt battery is not acceptable. Surprisingly there is no mention of maximum permissible operating voltage in the specification sheet, and it is entirely possible that 9v may have killed the chip.

It would also be a very good idea to fit all the external decoupling capacitors that they recommend.
Also known as the infamous "Warpspeed" on some other Forums.
Tony
 
Posts: 824
Joined: Sat Dec 03, 2005 12:34 pm
Location: Melbourne, Australia

Postby Nick » Mon Jan 09, 2006 11:03 pm

I used ta 9v because they showed a circuit using a 9v with a 7805 regulator On the Freescale site with a similar sensor. So the sensor never saw 9v only 5v. I did notice looking trough the app notes that there are some of those that only use 3 pins, (5v in, v out, and ground). This one I have has 6 pins that are used. (vout, VCC, G, V1, V2 Vex) I'm still not sure how to make it work, it's on the back burner until I have time to do more research. I have an extra that has not Been touched, in case I did fry it.



Nick
Nick
 
Posts: 144
Joined: Thu Oct 13, 2005 9:27 pm
Location: Yakima WA

Postby blown928 » Sun Feb 05, 2006 8:25 pm

New pics of the KISS bench....

Image

I've added a baffle around the exhaust flow tube so the motors aren't blowing directly on it

Image
The top showing the suck hole on the left and the blow hole on the right, the 2 valves for the flow elements at the back, and the red control box.



Image
Close up of the exhaust valve and the control box.


Image
My first victim. Note the cover plates on the blow & suck holes. This lets me compare the intake flow element readings to the exhause flow element readings for leakage testing.
Bill
'84 928s 5 sp. Vortech/749
blown928
 
Posts: 51
Joined: Fri Oct 28, 2005 9:03 pm
Location: Southern New England

Postby Tony » Sun Feb 05, 2006 8:41 pm

That is looking remarkably like my bench !

One thing I did was screw some bolts from inside the steel angle frame so the treaded ends project outward (like studs). The front cover panels are much easier and faster to replace, and there is no danger of crossing a thread and damaging the rather shallow threads in the angle frame.

That looks excellent, and I bet you have absolutely zero air leakage.
Also known as the infamous "Warpspeed" on some other Forums.
Tony
 
Posts: 824
Joined: Sat Dec 03, 2005 12:34 pm
Location: Melbourne, Australia

Postby blown928 » Mon Feb 06, 2006 6:52 pm

Right now I have some leakage around the valves. I assembled them without any silicone, thought the rubber seals would be enough but they weren't. I have to diasssemble and goop them up.

Tonight I'm hoping to do that and get the electronics installed so I can do a proper leak test. I expect the leakage to be very small, but we'll see.
Bill
'84 928s 5 sp. Vortech/749
blown928
 
Posts: 51
Joined: Fri Oct 28, 2005 9:03 pm
Location: Southern New England

Postby blown928 » Thu Feb 16, 2006 1:51 pm

Started up the bench with a manometer for the first time this afternoon. The digital stuff's not hooked up yet, I made a 48" vertical water-based manometer. I could pull 44" wc through one of my Porsche 928 intake ports with 4 of the 16-1234 motors. 3 motors on full and the one variable at about 1/2 let me dial in 28". I don't have the inclined manometer on the flow element yet so I don't know cfm.

A few initial thoughts:

Looks like 4 motors will be sufficient for now.

The router speed control works pretty well, I can dial in any depression I want up to the max the motors will pull. I need to wait a few seconds for the manometer to stabilize after an adjustment though.

I'm going to need stronger springs. I used springs from a TP roll holder ($0.97 at Wall Mart) and the valves just pulled open when I kicked on the second motor.

The sound insulation I added may have been worthless. It was pretty quiet until I mounted the head, then it got REAL loud sucking in through the intake. I'm going to need some ear protection.

The fun starts now :-)
Bill
'84 928s 5 sp. Vortech/749
blown928
 
Posts: 51
Joined: Fri Oct 28, 2005 9:03 pm
Location: Southern New England

Postby blown928 » Thu Mar 09, 2006 9:17 pm

Here's a pic of my head fixture, made from pine and 4"pvc pipe.
Bill
'84 928s 5 sp. Vortech/749
blown928
 
Posts: 51
Joined: Fri Oct 28, 2005 9:03 pm
Location: Southern New England

Previous

Return to Pitot Style Bench discussion

Who is online

Users browsing this forum: No registered users and 7 guests

cron