Page 1 of 1
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sat Dec 10, 2005 5:10 pm
by Peter
Here are some pics of my pitot style bench, bruce is making a calcibration plate for me and I"m going to paint the mdf next.
8 Ametek 116457-00 motors, controlled by 4 - 26 amp speed controls, 0-6 in. Dwyer inclined mano with 0-100% scale.
Bench
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sat Dec 10, 2005 7:13 pm
by Peter
Ok, try this again
Attached Image
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sat Dec 10, 2005 7:25 pm
by Peter
Third time
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sat Dec 10, 2005 7:27 pm
by bruce
........ Is a charm!
Looks good, thanks for sharing!
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sat Dec 10, 2005 7:28 pm
by Peter
OK, now I've got it, this is the air box
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sat Dec 10, 2005 7:32 pm
by Peter
And this is the inter cage that the mdf attaches to. 1.5 x 1.5 with welded nuts. It should make it pretty sturdy.
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sun Dec 11, 2005 5:02 am
by Nick
Turn up the heat!!!!!!!! It's only 60 in there. Just Kidding.
Looks good, I would like to see how it turns out.
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sun Dec 11, 2005 10:31 am
by larrycavan
Peter
Looking at the air box it looks like there are holes on both sides. Are you going to mount motors opposing each other in there?
Larry C
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sun Dec 11, 2005 1:11 pm
by Thomas Vaught
I too would be interested in how the flow works inside the box.
Very nice work. The steel framework is great. You might need a support in the center of the panels though as the forces can get pretty high.
Tom V.
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sun Dec 11, 2005 2:54 pm
by wing64k
Peter,Where did you get the black tube and collar on the side of the box and what size is it?
Thanks,Dean
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sun Dec 11, 2005 3:04 pm
by Peter
4 motors will be mounted on each side.
The blue and black ring is a 4' toliet ring available at Lowe's or Home Depot, it's supposed to be self sealing, but you'll see how I will take care of that in later photos.
As for support between the motors, I'll see if that will be necessay when I get it up and running, that's why I made the panels removeable.
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sun Dec 11, 2005 5:02 pm
by Thomas Vaught
So Peter, can I assume that the drums will be inside the box and the windings will go through the hole and discharge the air to the outside?
Tom V.
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Sun Dec 11, 2005 5:05 pm
by Peter
Correct, I'm only doing intake to start, intake and exhaust will be later.
![Post Post](./styles/silverwhite/imageset/icon_post_target.gif)
Posted:
Mon Dec 12, 2005 10:42 pm
by Peter
Here is my valve assembly, I got this idea from bruce's bench.
It will mount just in front of the air box.