[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4752: Cannot modify header information - headers already sent by (output started at [ROOT]/includes/functions.php:3887)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4754: Cannot modify header information - headers already sent by (output started at [ROOT]/includes/functions.php:3887)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4755: Cannot modify header information - headers already sent by (output started at [ROOT]/includes/functions.php:3887)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4756: Cannot modify header information - headers already sent by (output started at [ROOT]/includes/functions.php:3887)
Tractorsport Flowbench Forum Archive • View topic - Rob's bench (aka SuperRunner) - Mercdog/MSD style bench

Rob's bench (aka SuperRunner) - Mercdog/MSD style bench

A place to post links to your flowbench projects to share with everyone on the board.  You can share a description and pics also here please limit the size of your picture files to low res pics, Thanks

Postby SuperRunner » Sun Mar 12, 2006 3:31 pm

I fired it up last night with a 2 1/2 orifice. Sucked the water right out of the my 36 inch vertical manometer. I need to build some supports between the two plenum areas. The boards really start to cave in with that amount of depression.
Turbocharge EVERYTHING...that is how I see it.
SuperRunner
 
Posts: 92
Joined: Tue Feb 14, 2006 4:32 am
Location: utah

Postby Thomas Vaught » Sun Mar 12, 2006 6:49 pm

If you put a accumulator between the signal line for the test pressure and the manometer (Like a quart fruit jar with two nipples epoxied on the lid and a good canning seal) you will do two positive things:

You will dampen or eliminate any pulsations in the manometer caused by the plenum. Your manometer will be rock steady.

You will collect any water (or manometer fluid) that was pulled from the manometer and it can be used again.

A fruit jar is very strong in negative depression. A custom made accumulator could be made but it would not allow you to see how much fluid was trapped unless it was made from plexiglas.


Tom V.
Thomas Vaught
 
Posts: 465
Joined: Fri Feb 18, 2005 5:36 pm
Location: Michigan

Postby larrycavan » Sun Mar 12, 2006 8:45 pm

Really well built bench! I especially like the way you did the rear doors. Well supported all the way around. Individually removable...nice work!

Also, the accumulator is a great idea Tom..

Larry C
larrycavan
Site Admin
 
Posts: 1183
Joined: Fri Apr 01, 2005 4:40 pm

Postby SuperRunner » Wed Mar 15, 2006 5:02 am

Worked on it again some more tonight. Go the inclined manometer done, and the front panel mounted.

I didn't like how weak it was, so I put 2x4's on the top and the front. I can put my hole weight on it now and it won't budge. I will then also add support to the pleanum divider to the 2x4's.

And I went ahead and put to deck plates in the rear of the bench so I can have access to the lower plenum. I should have my 8" deck plate for the front by thursday.

Image

Image

Image
Turbocharge EVERYTHING...that is how I see it.
SuperRunner
 
Posts: 92
Joined: Tue Feb 14, 2006 4:32 am
Location: utah

Postby larrycavan » Wed Mar 15, 2006 9:57 pm

Again..nice work. Couple of things to look at. It's hard to tell from the pic.

Did you compensate your inclined scale for the .826 red fluid?

Is the test pressure manometer compensates as well?

Using 1.0 SG fluid in the test pressure manometer, your inch increment markings should be at .5" increments if you want to read directly on one side of the U tube...

Larry
larrycavan
Site Admin
 
Posts: 1183
Joined: Fri Apr 01, 2005 4:40 pm

Postby SuperRunner » Wed Mar 15, 2006 11:11 pm

Thanks.

Is the scale I have for .826 fluid, or can I use water, or does it matter?

My test pressure is set to 1 inch increments, but I have it labled as if it was .5". I might put .5" lines in there later.
Turbocharge EVERYTHING...that is how I see it.
SuperRunner
 
Posts: 92
Joined: Tue Feb 14, 2006 4:32 am
Location: utah

Postby Thomas Vaught » Thu Mar 16, 2006 10:50 pm

Because the U tube manometer goes up one leg and down the other leg you have to add the sum of the two legs. The other way is to make the 1 inch increments and then label them in 1/2 inch increments.

Trying to say a 1/2" movement on the one leg should be marked as 1 inch of test pressure. This way you only have to read one leg.

The inclined manometer fluid will move farther with the 8.26 fluid. Rocco's spreadsheet will allow you to adjust the well size to compensate.

Tom V.
Thomas Vaught
 
Posts: 465
Joined: Fri Feb 18, 2005 5:36 pm
Location: Michigan

Postby SuperRunner » Fri Mar 17, 2006 12:26 am

Yeah, that is how I have the U tube. Every real inch is 2" of water, so I don't have to add. Later I will put a small mark for the 1" of water.

I went and picked up some Dwyer fluid today, so all should be good, although I went ahead and ran some air throug my tubing with the reservoir still attached to get the water out and ...KABOOM!!!, guess I need to make another :)

I begin calibration tomorrow....YEAH!!!!
Turbocharge EVERYTHING...that is how I see it.
SuperRunner
 
Posts: 92
Joined: Tue Feb 14, 2006 4:32 am
Location: utah

Postby SuperRunner » Sat Mar 18, 2006 8:45 pm

Finished the bench today. I decided to go with a metal top. It is 3/8" steel, and I counter sunk all the screws that hold it down so it is flat. I also raised the top a little to fit additional instrumentation, and put a piece of acrylic to help divert the flow a little.

Image

Image

Image
Turbocharge EVERYTHING...that is how I see it.
SuperRunner
 
Posts: 92
Joined: Tue Feb 14, 2006 4:32 am
Location: utah

Postby Thomas Vaught » Sun Mar 19, 2006 12:33 pm

I think you are making great progress. The removable orifice deal should work ok too.

Tom V.
Thomas Vaught
 
Posts: 465
Joined: Fri Feb 18, 2005 5:36 pm
Location: Michigan

Postby adi111 » Sun Apr 02, 2006 7:43 am

Where is test pressure brass tube located?
Picture please
Thanks
adi111
 
Posts: 1
Joined: Tue Mar 14, 2006 8:56 am
Location: My room

Postby SuperRunner » Mon Apr 03, 2006 1:52 pm

it is in a picture above. It sits just below the acrylic baffle. I may move it to above the baffle, but I don't think it will make any difference. I have already tried several other locations, and it hasn't changed.

Also, I have both tubes for my inclined manometer on one side of my cabinet in the upper corners about 1-2 inches away from the outer wall and about 3 inches below the top of each chamber. My inclined manometer is as steady as a rock. I get soo little movement it is hardly detectable.
Turbocharge EVERYTHING...that is how I see it.
SuperRunner
 
Posts: 92
Joined: Tue Feb 14, 2006 4:32 am
Location: utah

Postby Thomas Vaught » Mon Apr 03, 2006 9:41 pm

You can make it move even less by putting a second tube with several small holes around the sensing tube. This eliminates any turbulence that may be in the cabinet from swirl in the plenums.

Tom V.
Thomas Vaught
 
Posts: 465
Joined: Fri Feb 18, 2005 5:36 pm
Location: Michigan

Previous

Return to Readers Flowbench projects

Who is online

Users browsing this forum: No registered users and 1 guest